|
#include "stdbool.h"
|
|
|
|
#ifndef CGLINE_H
|
|
#define CGLINE_H
|
|
|
|
//Physical values
|
|
|
|
#define OUT_VALUE_0 DALI_TX_PIN //Sende Wert mus logisch invertiert sein//L'envoi de la valeur doit ?tre invers? logiquement
|
|
#define OUT_VALUE_1 0x00
|
|
|
|
//Logical Values
|
|
#define CGL1_REC_ACTIVE 0x01 // True if reception has started
|
|
#define CGL2_REC_ACTIVE 0x02 // True if reception has started
|
|
#define CGL1_REC_ANSWER_ACTIVE 0x04 // True if transfer has started
|
|
#define CGL2_REC_ANSWER_ACTIVE 0x08 // True if transfer has started
|
|
#define CGL1_WAIT_ANSWER_ACTIVE 0x10 // True if Command was send and Waiting for Answer start-bit
|
|
#define CGL2_WAIT_ANSWER_ACTIVE 0x20 // True if Command was send and Waiting for Answer start-bit
|
|
#define CGL1_WAIT_END 0x1000
|
|
#define CGL2_WAIT_END 0x2000
|
|
|
|
#define CCB1_REC_ACTIVE 0x40 // True if reception has started
|
|
#define CCB2_REC_ACTIVE 0x80 // True if reception has started
|
|
#define CCB1_WAIT_ANSWER_ACTIVE 0x100
|
|
#define CCB2_WAIT_ANSWER_ACTIVE 0x200
|
|
|
|
#define CCB1_CHECKSUM_RECEIVED 0x400
|
|
#define CCB2_CHECKSUM_RECEIVED 0x800
|
|
|
|
#define CGL1_Start_RX 0x01 // True if RX prcess is able to start
|
|
#define CGL2_Start_RX 0x02 // True if RX prcess is able to start
|
|
|
|
//Events
|
|
#define IN_NEW_DATA 0x0001 // Set when new data has arrived
|
|
#define IN_SEND_ANSWER 0x0002 // Set when an answer is to be sent
|
|
#define IN_SIGNAL_ERROR 0x0004 // Set when the DALI signal level has been low for more than 500 ms
|
|
|
|
|
|
#define OUT_NEW_DATA 0x10 // Set when new data has arrived
|
|
#define OUT_SEND_DATA 0x20 // Set when an instruction is to be sent
|
|
#define OUT_ERROR_EVENT 0x40 // Set when the DALI signal level has been low for more than 500 ms
|
|
#define OUT_ANSWER_EVENT 0x80 //
|
|
#define OUT_ANSWER_DETECTED 0x08 // Set if the device has answered
|
|
#define OUT_BUS_QUALETY_OK 0x04 // Set if the bus qualety is IO
|
|
|
|
#define DEFAULT_NR_LINES 4
|
|
#define DEFAULT_MAX_LAMPS 200 //Set max amount of lamps per line
|
|
#define DEFAULT_MAX_ZONE 4
|
|
#define SCAN_REPETITION_10MIN 60
|
|
#define MAX_100_LUMS_LINE 200
|
|
|
|
void ReceiveDaliMessage();
|
|
void RX_Interrupt_Handler(uint8 ui8_Line);
|
|
|
|
#endif
|